Heating and air conditioning for Mazda CX-5 (KE)

Technical data
1. Front heater air duct. 2. Main damper for selecting air flow modes. 3. Cabin filter. 4. Rear heater air duct. Versions with SKYACTIV-G 2.0 engine: 5. Refrigerant...

Precautions when working with refrigerant
Only lubricants recommended for air conditioning systems and air conditioning system parts may be used. Using lubricants other than those recommended may cause...

Precautions for compressor maintenance
Close all openings to prevent moisture and foreign objects from entering. When the compressor is removed, store it in the position in which it is installed on the...

Service data
Note: The refrigerant used in the air conditioning system may differ depending on the country for which the vehicle is intended. When removing and refilling the...

Cabin filter
Replacing the cabin filter 1. Remove the glove box. 2. Remove the cabin filter. 3. Installation is carried out in reverse order. Checking the cabin filter Check the...

Removal and installation the ventilation unit
1. Disconnect the negative battery terminal. 2. Remove the following parts: Front door sill trim on the passenger side. Front side trim on the passenger side. The lower...

Removal and installation the front heater ducts
1. Disconnect the negative battery terminal. 2. Remove the lower cover of the instrument panel. 3. Disconnect the clips and remove the front air duct. 4. Installation is...

Removal and installation rear heater ducts
1. Disconnect the negative battery terminal. 2. Remove the following parts: Versions with manual transmission: gearshift knob. Front console box. Shift Lever Panel. Top...

Removal and installation heater hoses
1. Remove the battery. 2. Drain the coolant from the engine. 3. Remove the insulator. 4. Remove the clamps and disconnect the heater hoses. Versions with temperature...

Air conditioning system
To perform any work related to the air conditioning system, special equipment is required - a station for removing and charging the refrigerant. When performing work, it...

Air conditioning control
Automatic climate control system: 1. Passenger compartment temperature sensor. 2. Mixing flap drive on the driver's side. 3. Evaporator temperature sensor. 4. Mode...

Removal and installation the intake flap drive
1. Disconnect the negative battery terminal. 2. Remove the glove box. 3. Disconnect the intake flap drive connector. 4. Loosen the screws and remove the intake flap...

Removal and installation the fan motor
1. Disconnect the negative battery terminal. 2. Remove the lower cover of the instrument panel. 3. Disconnect the connector. 4. Loosen the screws. 5. Remove the fan...

Removal and installation the mixing flap drive
From the driver's side 1. Disconnect the negative battery terminal. 2. Remove the following parts: Side wall on the driver's side. Left front heater air duct. 3....

Removal and installation the ambient temperature sensor
1. Disconnect the negative battery terminal. 2. Remove the front bumper from the car. 3. Disconnect the connector. 4. Remove the ambient temperature sensor. 5....

Removal and installation the automatic climate control unit
Note: The climate control unit stores vehicle-specific information. A new climate control unit does not contain such information. When the ignition is turned on after...

Removal and installation the control unit of the air conditioning system with manual control
Removal 1. Disconnect the negative battery terminal. 2. Remove the following parts: Versions with manual transmission: gearshift knob. Glove compartment. Front console...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• User manual: Air conditioning and heater Mazda3 BK (2003-2009)
• User manual: Air conditioning and heater Mazda6 GG (2002-2008)
• Body: Heating system Mazda 121 (3) (1996-2003)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

CX-5KE (2012-2017)