External body elements Mazda CX-5 (KE)
Technical data
The Mazda CX-5 has a load-bearing body structure. The use of zones with programmable deformation in the body structure allows not only to significantly dampen the force...
The Mazda CX-5 has a load-bearing body structure. The use of zones with programmable deformation in the body structure allows not only to significantly dampen the force...
Plastic body parts
Note: Using temperatures higher than the specified values may cause deformation of the part.
Note: Using temperatures higher than the specified values may cause deformation of the part.
Exterior — device
1. Mounting plate. 2. Casing panel. 3. Hood cover. 4. Upper sealing panel. 5. Upper casing beam. 6. Hood panel. 7. Front wing. 8. Fuel filler flap. 9. Front wing trim....
1. Mounting plate. 2. Casing panel. 3. Hood cover. 4. Upper sealing panel. 5. Upper casing beam. 6. Hood panel. 7. Front wing. 8. Fuel filler flap. 9. Front wing trim....
Protective body trays
Removal and installation the front protective tray No.1 1. Loosen bolts A. 2. Remove the fasteners B. 3. Loosen screws C. 4. Remove the front protective tray No.1 in the...
Removal and installation the front protective tray No.1 1. Loosen bolts A. 2. Remove the fasteners B. 3. Loosen screws C. 4. Remove the front protective tray No.1 in the...
Removal and installation the hood cover
Warning: Removing the hood without support may cause it to fall and cause serious injury. At least one other person is required to remove the hood. 1. Disconnect the...
Warning: Removing the hood without support may cause it to fall and cause serious injury. At least one other person is required to remove the hood. 1. Disconnect the...
Adjusting the position of the bonnet lid
Height adjustment 1. Make sure that the height difference between the hood and body surfaces is within the norm. a: 2.7-6.9 mm. b: 4.1~8.0mm. 2. Disconnect the negative...
Height adjustment 1. Make sure that the height difference between the hood and body surfaces is within the norm. a: 2.7-6.9 mm. b: 4.1~8.0mm. 2. Disconnect the negative...
Fuel filler neck hatch
Removal and installation the fuel filler flap 1. Loosen the bolts. 2. Remove the fuel filler cap. 3. Installation is carried out in the reverse order of removal. 4....
Removal and installation the fuel filler flap 1. Loosen the bolts. 2. Remove the fuel filler cap. 3. Installation is carried out in the reverse order of removal. 4....
Removal and installation the front bumper
Caution: To prevent scratches and damage to the paintwork, apply protective tape to the positions shown in the figure. 1. Disconnect the negative battery terminal. 2....
Caution: To prevent scratches and damage to the paintwork, apply protective tape to the positions shown in the figure. 1. Disconnect the negative battery terminal. 2....
Removal and installation the front bumper support element
1. Disconnect the negative battery terminal. 2. Remove the following parts: Upper sealing panel. Front bumper. Front combination lights. Mounting plate. Energy...
1. Disconnect the negative battery terminal. 2. Remove the following parts: Upper sealing panel. Front bumper. Front combination lights. Mounting plate. Energy...
Removal and installation bumper sliders
Front bumper sliders 1. Disconnect the negative battery terminal. 2. Remove the upper sealing panel. 3. Remove the front bumper. 4. Loosen bolts A. 5. Pull the front...
Front bumper sliders 1. Disconnect the negative battery terminal. 2. Remove the upper sealing panel. 3. Remove the front bumper. 4. Loosen bolts A. 5. Pull the front...
Removal and installation the rear bumper
Caution: To prevent scratches and damage to the paintwork, apply protective tape to the positions shown in the figure. 1. Disconnect the negative battery terminal. 2....
Caution: To prevent scratches and damage to the paintwork, apply protective tape to the positions shown in the figure. 1. Disconnect the negative battery terminal. 2....
Removal and installation the rear bumper support element
1. Disconnect the negative battery terminal. 2. Remove the following parts: Rear mudguards. Rear combination lights. Rear bumper. 3. Remove the rubber suspension in the...
1. Disconnect the negative battery terminal. 2. Remove the following parts: Rear mudguards. Rear combination lights. Rear bumper. 3. Remove the rubber suspension in the...
Removal and installation the front wing
1. Disconnect the negative battery terminal. 2. Remove the following parts: Front bumper. Front combination headlight. Front bumper slider. 3. Remove the front fender...
1. Disconnect the negative battery terminal. 2. Remove the following parts: Front bumper. Front combination headlight. Front bumper slider. 3. Remove the front fender...
Removal and installation the rear wing trim
1. Remove fasteners A. 2. Pull the rear fender trim in the direction of the arrow (2) to release clips B, C and D. 3. Installation is carried out in the reverse order of...
1. Remove fasteners A. 2. Pull the rear fender trim in the direction of the arrow (2) to release clips B, C and D. 3. Installation is carried out in the reverse order of...
Removal and installation the side door
Attention. Removal the door without support may cause it to fall and cause serious injury. Always remove the door with the help of another person to prevent the door...
Attention. Removal the door without support may cause it to fall and cause serious injury. Always remove the door with the help of another person to prevent the door...
Door adjustment
1. Check the size of the gaps and the difference in height between the door panels and the body. 2. Loosen the door hinge mounting bolts and adjust the position of the...
1. Check the size of the gaps and the difference in height between the door panels and the body. 2. Loosen the door hinge mounting bolts and adjust the position of the...
Removal and installation the trunk door
Caution. Removing the shock absorber strut, tailgate hinge mounting bolts, or the tailgate itself without support may cause the tailgate to fall and cause injury....
Caution. Removing the shock absorber strut, tailgate hinge mounting bolts, or the tailgate itself without support may cause the tailgate to fall and cause injury....
Adjusting the trunk door
1. Check the size of the gaps and the difference in height between the door panels and the body. 2. Loosen the door hinge mounting bolts and adjust the position of the...
1. Check the size of the gaps and the difference in height between the door panels and the body. 2. Loosen the door hinge mounting bolts and adjust the position of the...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
More sections on repairs of other Mazda models
• Body: Exterior (external elements) Mazda Capella 3 (1982-1992, petrol)
• Body: Exterior (external elements) Mazda6 GG (2002-2008)
• Body: Exterior (external elements) Mazda BT-50 (1) (2006-2011)
• Body: Exterior (external elements) Mazda Capella 3 (1982-1992, petrol)
• Body: Exterior (external elements) Mazda6 GG (2002-2008)
• Body: Exterior (external elements) Mazda BT-50 (1) (2006-2011)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Introduction to the guide
- User manual
- Maintenance
- Power unit
- Petrol engines 2.0 l
- Petrol engines 2.5 l
- Diesel engines 2.2 l
- Cooling system
- Lubrication system
- Supply system
- Control system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Transfer case
- Drive shafts and cardan
- Chassis
- Wheels and tires
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Security systems
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Electrical circuits