Car clutch Mazda CX-5 (KE)

Clutch C66M-R, C66MX-R — technical data
Clutch C66M-R, C66MX-R: 1. Clutch hydraulic fluid reservoir. 2. Clutch master cylinder. 3. Clutch pedal. 4. Clutch hydraulic line. 5. Clutch slave cylinder. 6. Clutch...

Clutch D66M-R, D66MX-R — technical data
Clutch D66M-R, D66MX-R: 1. Clutch hydraulic fluid reservoir. 2. Clutch master cylinder. 3. Clutch pedal. 4. Clutch hydraulic line. 5. Clutch slave cylinder. 6. Clutch...

Checking the level of the working fluid of the clutch hydraulic drive
Note: This reservoir is used for the clutch and brake hydraulic system. 1. Make sure that the clutch hydraulic fluid level is between the MIN and MAX marks. 2. If the...

Checking for leaks in the clutch hydraulic fluid
Caution. Do not allow brake fluid to come into contact with painted surfaces. This fluid contains substances that can dissolve the body paint. If brake fluid comes into...

Replacing the clutch hydraulic fluid/bleeding air from the system
Attention. Do not allow brake fluid to come into contact with painted surfaces. This fluid contains substances that can dissolve the body paint. If brake fluid comes...

Clutch pedal
Note: When checking the clutch pedal, please note the following: Each measurement is taken from the center of the top surface of the pedal pad. If measuring the distance...

Removal and installation the clutch pedal
Attention. Fix the steering wheel with tape or wire to prevent the steering shaft from turning when disconnected. If the steering wheel is turned after the steering...

Removal and installation the clutch pedal position sensor
1. Disconnect the negative battery terminal. 2. Disconnect the clutch pedal position sensor connector. 3. Turn the clutch pedal position sensor 45° counterclockwise....

Removal and installation the starter interlock switch
1. Disconnect the negative battery terminal. 2. Disconnect the starter lock switch connector. 3. Remove the starter interlock switch: Detach hook A in the direction of...

Removal and installation the clutch master cylinder
Attention. Fix the steering wheel with tape or wire to prevent the steering shaft from turning after disconnecting. If the steering wheel is turned after the steering...

Removal and installation the clutch travel sensor
Note: The clutch travel sensor is installed only on vehicles with the i-stop system. The clutch stroke sensor is built into the clutch master cylinder. 1. Replace the...

Removal and installation of hydraulic clutch lines and hoses
Caution. Do not allow brake fluid to come into contact with painted surfaces. This fluid contains substances that can dissolve the body paint. If brake fluid comes into...

Removal and installation the clutch slave cylinder
Caution. Do not allow brake fluid to come into contact with painted surfaces. This fluid contains substances that can dissolve the body paint. If brake fluid comes into...

Removal and installation the clutch mechanism
Note: Removal and installation of the clutch mechanism is shown using the example of the C66M-R, C66MX-R clutch. 1. Dust cover. 2. Clutch release fork. 3. Clutch release...

Checking the clutch mechanism components
Checking the clutch release bearing Caution: Do not use cleaning agents or a steam cleaner to clean the clutch release bearing as the bearing is filled with grease. 1....

Special tools and accessories

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Transmission: Clutch Mazda Familia 6 (1989-1994)
• Transmission: Clutch and drive shafts Mazda Capella 3 (1982-1992, petrol)
• Transmission: Clutch Mazda3 BK (2003-2009)
• Transmission: Clutch Mazda6 GG (2002-2008)
• Transmission: Clutch Mazda BT-50 (1) (2006-2011)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

CX-5KE (2012-2017)