Gasoline engines 2.0 l car Mazda CX-5 (KE)

Technical data
1. Engine assembly. 2. Automatic tensioner of the attachment drive belt. 3. Attachment drive belt. 4. Oil control valve (OCV). 5. Decorative engine cover. 6. Hydraulic...

Preparing for engine parameter checks
Note: If the accelerator pedal is continuously depressed for a certain period of time, the engine speed may drop to idle speed. This is due to the fuel cut control...

Checking the idle speed
Note: The idle speed is not adjustable. The M-MDS device is used to check the idle speed. 1. Prepare for engine parameter checks. 2. Make sure that the engine idle speed...

Checking the ignition timing
Note: The ignition timing angle is not adjustable. The M-MDS device is used to check the ignition timing. 1. Prepare for engine parameter checks. 2. Check the ignition...

Checking idle parameters
1. Make sure that the idle speed and ignition timing are within the normal range (see above). 2. Insert the exhaust gas analyzer into the exhaust pipe. 3. Make sure that...

Checking for increased idle speed
Note: The idle speed is not adjustable. The M-MDS device is used to check the idle speed. 1. Prepare for engine parameter checks. 2. Check that the engine idle speed...

Checking the compression in the cylinders
Attention. Hot engine and oil can cause burns. Be careful not to burn yourself when removing/installing various components. Fuel vapors are hazardous and flammable,...

Checking the drive belts of the accessory equipment
Generator drive belt Note: Due to the use of an automatic tensioner, checking the alternator drive belt deflection/tension is not necessary. 1. Check that the hexagonal...

Replacing the drive belts of the attachments
Warning: A hot engine can cause burns. Before starting work, turn off the engine and wait until it cools down. Note: Removal / installation of drive belts is carried out...

Checking the automatic drive belt tensioner
Attention. A hot engine can cause burns. Before starting work, turn off the engine and wait until it cools down. If the rubber part of the automatic drive belt tensioner...

Removal and installation the timing chain
1. Oil dipstick. 2. Cylinder head cover. 3. Oil spray tubes. 4. Automatic drive belt tensioner. 5. Water pump pulley. 6. Crankshaft pulley bolt. 7. Crankshaft pulley. 8....

Hydraulic valve timing controller
Checking the hydraulic valve timing regulator Attention. A hot engine can cause burns. Before starting work, turn off the engine and wait until it cools down. Do not...

Electric valve timing controller
Checking the electric valve timing motor Attention. A hot engine can cause burns. Before starting work, turn off the engine and wait until it cools down. Do not...

Possible malfunctions of hydraulic clearance compensators
Note:*: period of time during which oil flows to hydraulic compensators; this value includes the ambient temperature tolerance and the type of oil used.

Checking hydraulic compensators
1. Disconnect the negative battery terminal. 2. Remove the decorative engine cover. 3. Remove the ignition coils/ion sensors. 4. Remove the cylinder head cover (see...

Removal and installation of timing components
Attention. A hot engine can cause burns. Before starting work, turn off the engine and wait until it cools down. If the camshaft is rotated after the drive chain is...

Removal and installation the cylinder head
Attention. Hot engine and oil can cause burns. Be careful not to burn yourself when removing/installing various components. Fuel vapors are hazardous and flammable,...

Replacing the front crankshaft oil seal
1. Crankshaft pulley bolt. 2. Crankshaft pulley. 3. Front crankshaft oil seal. Warning: A hot engine can cause burns. Before starting work, turn off the engine and wait...

Replacing the rear crankshaft oil seal
1. Rear crankshaft oil seal. 1. Remove the gearbox from the engine. 2. Remove the flywheel (manual transmission) or drive disk (automatic transmission). 3. Cut off the...

Removal and installation the decorative engine cover
Caution: If the elastic element is lifted only on one side of the decorative engine cover, the locking adapter shown in the figure may be damaged. When removing the...

Removal and installation the engine assembly
Front-wheel drive (2WD) only versions: 1. Bracket plate. 2. Front subframe with engine mounting support cushion No.1. Z. Engine mounting support bracket No.1. 4. Engine...

Special tools and accessories

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Power unit: Petrol engines Mazda Familia 6 (1989-1994)
• Power unit: Petrol engines 1.6 and 1.8 Mazda Capella 5 (1991-1997)
• Power unit: Petrol engine 1.25/1.4 l Mazda 121 (3) (1996-2003)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

CX-5KE (2012-2017)