Electrical equipment of car engines Mazda CX-5 (KE)

Charging system — technical data
1. Generator. 2. Battery. 3. DC-DC converter (cars with i-stop system). Note: The layout of the starting system components is shown using a gasoline engine as an...

Launch system
An intermediate starter switch, which is installed on vehicles with a manual transmission, prevents the vehicle from moving when the engine is started, thus increasing...

Ignition system (petrol engines)
The ignition system of SKYACTIV gasoline engines uses individual ignition coils placed directly on the spark plugs. Each ignition coil has an ion sensor built into it....

Pre-heating system (diesel engines)
The SKYACTIV-D 2.2 diesel engine has a relatively low compression temperature due to low compression. The preheating system increases the compression temperature by...

Cruise control
Components of a gasoline-powered vehicle's cruise control system Components of a Diesel Car Cruise Control System The cruise control system ensures that the vehicle...

Battery checks
Attention. The battery contains toxic substances. Handle the battery with care. Since battery electrolyte is highly corrosive, be careful not to allow it to come into...

Disconnecting/connecting the negative battery terminal
Caution: Before removing components of the passive restraint system, it is necessary to disconnect the negative terminal of the battery and wait at least one minute to...

Removal and installation the battery
Battery pack for petrol engine versions: 1. Negative terminal of the battery. 2. Positive terminal of the battery. 3. Battery bracket. 4. Battery assembly. 5. Battery...

Operations after replacing the battery (vehicles with i-stop system)
Note: If the number of charges/discharges (working cycles) exceeds the set value, a corresponding fault code is generated and the orange i-stop indicator starts...

Removal and installation the generator
Versions with petrol engines Gasoline Engine Generator: 1. Generator drive belt tensioner. 2. Terminal B of the generator. 3. Generator connector. 4. Generator....

Checking the generator
Caution: Do not apply battery positive voltage to the alternator D terminal, otherwise it may damage the internal components (power transistor) generator. Checking the...

Disassembly and assembly of the generator
Attention. Solder the contacts quickly with a soldering iron, otherwise the diodes (rectifiers) and transistors can be damaged due to overheating. Disassembly and...

Checking the generator components
Rotor 1. Using a tester, measure the resistance between the contact rings. If the measured value is not within the norm (1.8-2.1 Ohm at 20°C), replace the rotor with a...

Removal and installation the starter
Gasoline engine starter: 1. Output terminal B. 2. S-output connector. 3. Starter. Diesel engine starter: 1. Output terminal B. 2. S-output connector. 3. Starter....

Operations after replacing the starter (cars with i-stop system)
Note: If the starter has exhausted its resource after a certain number of engine starts, or if malfunctions occur in various components of the i-stop system, the orange...

Disassembling and assembling the starter
Disassembly and assembly of the starter is carried out according to the general view figure below in numerical order. 1. Magnetic switch. 2. Adjusting washer. 3. Back of...

Checking the starter
Check on the car 1. Make sure the battery is fully charged. 2. The starter is normal if it rotates smoothly and without any extraneous noise. If the starter does not...

Checking the intermediate starter switch
Caution: Do not reuse the starter intermediate switch if it has been removed from the vehicle at least once. Replace the starter intermediate switch with a new one after...

Ignition coils
Removal and installation ignition coils with ion sensors 1. Disconnect the negative battery terminal. 2. Remove the decorative engine cover. 3. Disconnect the connector,...

Spark plugs
Removal and installation spark plugs Caution: Using spark plugs other than the recommended type will reduce engine performance. When replacing, install only the...

Glow plugs (diesel engines)
Checking glow plugs 1. Disconnect the glow plug wires. 2. Measure the resistance between the glow plug terminal and the housing ground. If the measured value is not...

Pre-heating control unit
Removal and installation the pre-heating control unit 1. Disconnect the negative battery terminal. 2. Remove the battery from the shelf. 3. Disconnect the connector and...

Cruise control switch
1. Disconnect the negative battery terminal and wait at least one minute. 2. Remove the driver's side airbag module. 3. Disconnect the contact disk connector. 4. Using a...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Power unit: Engine electrics Mazda Capella 6 (1997-2005, petrol)
• Power unit: Engine electrical equipment Mazda3 BK (2003-2009)
• Power unit: Electrical equipment of engines Mazda6 GG (2002-2008)
• Power unit: Engine electrical equipment Mazda BT-50 (1) (2006-2011)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

CX-5KE (2012-2017)