Brake system of the car Mazda CX-5 (KE)

Technical data — service brake system
Front part of the brake system: 1. highway. 2. Brake fluid. Z. Master brake cylinder. 4. Vacuum brake booster. 5. Brake booster vacuum sensor (cars with i-stop system)....

Technical data — Parking brake system
1. Parking brake lever. 2. Parking brake switch. 3. Front parking brake cable. 4. Rear parking brake cable. The parking brake system uses the rear brakes to prevent the...

Dynamic stabilization system
The Dynamic Stability Control (DSC) system is designed to maintain vehicle stability and controllability by identifying and eliminating critical situations in advance....

General procedures for working with the brake system
Installing wheels on a car When installing wheels on a vehicle, tighten the wheel nuts in a cross pattern to a torque of 108-147 Nm. Disconnecting the brake lines If any...

Brake fluid
Checking the brake fluid level Make sure that the brake fluid level in the reservoir is between the MAX and MIN marks. If the brake fluid level is below the MIN mark,...

Checking, removing and installing the vacuum hose
Checking the vacuum hose 1. Remove the vacuum hose. 2. Make sure that air flows freely through the vacuum hose from the brake booster side to the vacuum pump side and...

Checking the brake booster
Note: The following testing methods allow you to easily determine the functionality of the brake booster. If any faults are detected in the vacuum booster, replace the...

Removal and installation the brake booster
1. Vacuum hose 2. Spring pin. 3. Connecting pin. 4. Fastening nut. 5. Vacuum brake booster. 6. Gasket. Note: replace the part with a new one after each removal. Caution:...

Removal and installation a vacuum pump
Checking the vacuum pump 1. Remove the decorative engine cover. 2. Use pliers to loosen the clamp and disconnect the vacuum hose from the vacuum pump. 3. Install the...

Checking the brake pedal
Checking the pedal height 1. Measure the distance from the center of the top surface of the pedal pad to the floor covering and compare the obtained value with the...

Removal and installation the brake pedal
1. Brake switch connector and wiring. 2. Brake switch. 3. Spring pin. 4. Connecting pin. 5. Upper nuts of the pedal block. 6. Lower nuts of the pedal block. 7. Brake...

Master brake cylinder
Removal and installation the master brake cylinder 1. Brake fluid level sensor connector. 2. Spare clutch hydraulic hose (versions with manual transmission). 3. Hose...

Checking the front disc brakes
Measures to eliminate brake judder Shocks in the brake mechanisms appear in three forms: The steering wheel vibrates in the direction of the turn. This is most...

Removal and installation front brake components
1. Remove the front disc brake components in the order shown in the figure. 1. Bolt. 2. Brake hose 3. Bolt. 4. Support. 5. Brake pads. 6. Gaskets. 7. Holders. 8. Bolts....

Replacing the front brake pads
1. Remove the components in the numbered order shown in the figure. 1. Bolt. 2. Brake caliper. 3. Brake pads. 4. Gaskets. 5. Brake shoe holders. 2. Installation is...

Disassembling and assembling the front brake caliper
1. Bleed nipple cap. 2. Bleeding nipple. 3. Piston. 4. Dust cover. 5. Piston seal. 6. Caliper body. Note: : replace the part with a new one after each removal. : apply...

Removal and installation the front brake hose
1. Remove the brake hose in the sequence shown in the figure. 1. Brake pipe. 2. Clamp. 3. Bolt. 4. Brake hose Note: replace the part with a new one after each removal....

Checking the rear disc brakes
Measures to eliminate brake judder Shocks in the brake mechanisms appear in three forms: The steering wheel vibrates in the direction of the turn. This is most...

Removal and installation rear brake components
1. Loosen the parking brake adjusting nut. 2. Remove the rear disc brake components in the sequence shown in the figure. 1. Parking brake cable. 2. Hollow bolt. 3. Brake...

Replacing rear brake pads
1. Remove the components in the numbered order shown in the figure. 1. Bolts. 2. Support. 3. Brake pads. 4. Gaskets. 5. Holders. Note: use a special tool or device. 2....

Disassembling and assembling the rear brake caliper
1. Bleed nipple cap. 2. Bleeding nipple. 3. Piston. 4. Dust cover. 5. Piston seal. 6. Caliper body. Note: : replace the part with a new one after each removal. : use a...

Removal and installation the rear brake hose
1. Remove the brake hose in the sequence shown in the figure. 1. Brake pipe. 2. Clamp. 3. Bolt. 4. Brake hose. Note: replace the part with a new one after each removal.

Removal, installation and adjusting the parking brake lever
Removal and installation the parking brake lever 1. Remove the front console box. 2. Versions with manual transmission: remove the gearshift knob. 3. Remove the shift...

Parking brake lever
Checking the travel of the parking brake lever 1. Press the brake pedal several times. 2. Pull the parking brake lever twice or three times. 3. Check the movement of the...

Parking brake cables
Removal and installation the front parking brake cable 1. Adjusting nut. 2. Front parking brake cable. 1. Remove the front console box. 2. Versions with manual...

Checking the Parking Brake Switch
1. Disconnect the parking brake switch connector. 2. Check the continuity of the circuit between the connector terminal and the housing ground according to the table...

DSC hydro-electronic control unit
Removal and installation of the hydroelectronic control unit 1. DSC electronic unit connector. 2. Brake lines. 3. Nuts. 4. Bolt. 5. DSC hydro-electronic control unit...

Initialization procedure for the dynamic stabilization system sensors
Caution. If the initialization procedure of the dynamic stability system sensors is not completed, the system will not operate correctly and may cause a traffic...

Removal and installation ABS wheel sensors
Front ABS wheel sensors 1. Connector. 2. Bolt. 3. Wheel ABS sensor. 1. Remove the mudguard. 2. Disconnect the ABS wheel sensor connector. 3. Loosen the mounting bolt and...

Checking the brake fluid pressure sensor
1. Turn off the ignition. 2. Remove the fasteners. 3. Move the mudguard aside. 4. Disconnect the brake line from the left front brake hose. 5. Remove the clamp. 6....

Special tools and accessories

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Chassis: Brake system Mazda Familia 5 (1985-1989)
• Chassis: Brake system Mazda Capella 3 and 4 (1982-1992)
• Chassis: Brake system Mazda3 BK (2003-2009)
• Chassis: Brake system Mazda6 GG (2002-2008)
• Chassis: Brake system Mazda 121 (3) (1996-2003)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

CX-5KE (2012-2017)