Automatic transmission cars Mazda CX-5 (KE)

Technical data
1. Drive disk. 2. Automatic transmission. 3. Differential seals. 4. Electric pump of working fluid of automatic transmission (if equipped). 5. Valve body seal. 6. Valve...

Checking the mechanical part
1. Securely apply the parking brake and place wheel chocks under the front and rear wheels. 2. Check the engine coolant level. 3. Check the engine oil level. 4. Check...

Checking the main pressure
1. Perform mechanical check as described above. 2. Remove the air filter. 3. Remove the wiring bracket. Gearboxes FW6A-EL, FW6AX-EL Gearboxes GW6A-EL, GW6AX-EL 4....

Stop check
1. Perform mechanical check as described above. 2. Securely apply the parking brake and place wheel chocks under the front and rear wheels. 3. Start the engine. 4....

Checking the switching delay
1. Perform mechanical check as described above. 2. Securely apply the parking brake and place wheel chocks under the front and rear wheels. 3. Start the engine. 4....

Road check
Please note: To perform the test drive, you must select a safe area without heavy traffic. Note: When performing a road test of an automatic transmission, if the...

Automatic transmission fluid
Checking the automatic transmission fluid level Warning. If the automatic transmission fluid level is not correct, or there is no fluid on the dipstick after the engine...

Automatic transmission fluid replacement
Caution: Do not service the transmission if the automatic transmission fluid is hot. Otherwise, there is a risk of serious burns. 1. Remove the front protective tray...

Adjusting the level of the working fluid of the automatic transmission
Attention. Adjustment of the automatic transmission fluid level should be performed only when the fluid temperature is 45-55°C. If the fluid level is not correct, the...

Removal and installation an electric oil pump
Attention. Do not drop or subject the electric automatic transmission oil pump to impact. If the pump is dropped or subjected to impact, replace it with a new one. Do...

Removal and installation the gearbox oil cooler
1. Disconnect the negative battery terminal. 2. Remove the front protective tray No.2. 3. Drain the automatic transmission fluid. 4. Drain the engine coolant. 5. Remove...

Initialization and Configuration Procedures — Initial Training
If the valve body and pressure sensor have been replaced with new ones, it is imperative that the initial learning procedure be performed. If the initial learning...

Transmission Control Unit Configuration
Note: The transmission control unit is integrated into the valve body. 1. Make sure that the configuration procedure is necessary after replacing a particular part. 2....

Removal and installation the valve body
Note: Removal of the automatic transmission from the vehicle is not required to remove and install the valve body. Removal Attention. A hot transmission and automatic...

Automatic transmission shift mechanism
1. Selector drive cable. 2. Selector lever assembly.

Removal and installation the selector drive cable
1. Disconnect the negative battery terminal. 2. Perform the following procedure to remove the selector drive cable from the selector lever side: Remove the front...

Adjusting the selector drive cable
1. Disconnect the negative battery terminal. 2. Remove the switch panel. 3. Loosen the bracket mounting screws. 4. Remove the bracket from the rear console. 5. Move the...

Removal and installation the selector lever assembly
1. Disconnect the negative battery terminal. 2. Remove the front console. 3. Disconnect the selector lever connector. 4. Remove the selector drive cable (see above). 5....

Removal and installation the selector illumination lamp
1. Disconnect the negative battery terminal. 2. Remove the switch panel. 3. Remove the socket from the switch panel. 4. Remove the selector illumination lamp from the...

Position sensor M
Checking the continuity of the M position sensor circuit Note: The M position sensor is built into the selector lever assembly. 1. Disconnect the negative battery...

Gear Boost switch
Checking the continuity of the upshift switch circuit Note: The upshift switch is built into the selector lever assembly. 1. Disconnect the negative battery terminal. 2....

Downshift switch
Checking the continuity of the downshift switch circuit Note: The downshift switch is built into the selector lever assembly. 1. Disconnect the negative battery...

Shift lock mechanism
Checking the shift lock mechanism 1. Turn on the ignition (engine off). 2. Move the selector lever to position P. 3. Check that the selector lever does not shift from...

Shift Lock Solenoid
Checking the shift lock solenoid Note: The shift lock solenoid is built into the selector lever assembly. 1. Disconnect the negative battery terminal. 2. Remove the...

Position sensor other than P
Checking a position sensor other than P Note: The non-P position sensor is built into the selector lever assembly. 1. Disconnect the negative battery terminal. 2. Remove...

Replacing differential seals
From the gearbox side 1. Remove the front protective tray No.2. 2. Drain the automatic transmission fluid. 3. Disconnect the left front drive shaft from the gearbox....

Valve body seal
Replacing the valve body seal 1. Disconnect the negative battery terminal. 2. Remove the engine air filter. 3. Disconnect the valve body connector. Attention. Be careful...

Special tools and accessories

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Transmission: Automatic gearbox Mazda Familia 5 (1985-1989)
• Transmission: Automatic gearbox Mazda Capella 5 (1991-1997)
• Transmission: Automatic gearbox Mazda3 BK (2003-2009)
• Transmission: Automatic gearbox Mazda6 GG (2002-2008)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

CX-5KE (2012-2017)