MazBook.ru
English Русский
Български
Беларускі
Український
Српски
Hrvatski
Română
Polski
Slovenský
Magyar
• Bookmark • Sitemap • Contacts •   
Cars Opel Cars Ford Cars Volkswagen Cars Audi Cars Kia Cars Renault Cars Peugeot
 
 
 
 
 
 
 
Familia Capella Mazda3 Mazda6 CX-? Others Articles
CX-5KE (2012-2017)

Removal and installation the selector drive cable (Mazda CX-5KE)

  • Home
  • Mazda CX-?
  • CX 5 KE (2012-2017)
  • Transmission
  • Automatic gearbox
  • Removal and installation the selector drive cable
0
1. Disconnect the negative battery terminal.

2. Perform the following procedure to remove the selector drive cable from the selector lever side:
  • Remove the front console.
  • Remove the safety lock in the direction of the arrow (1) in the figure, then remove the locking element in the direction of the arrow (2) in the figure and unlock the cable.

Remove the safety lock in the direction of the arrow (1) in the figure, then remove the locking…


By pressing the outer end plate of the cable (from the selector lever side) in the direction of the arrow (3) in the figure, pry up the outer end of the cable (from the selector lever side) in the direction of the arrow (4) in the figure to detach the cable from the bracket.

By pressing the outer end plate of the cable (from the selector lever side) in the direction of the…


(The original article is on: «MAZBOOK.ru»)

Remove the outer end of the cable (from the selector lever side) from the bracket.



Remove the drive cable end from the selector lever.

Remove the drive cable end from the selector lever.


3. Perform the following procedure to remove the selector cable from the transmission side:

Remove the engine air filter housing.

Remove the battery from the shelf.

Pressing the bracket bar in the direction of the arrow (5) in the figure, pry up the outer end of the cable (from the gearbox side) in the direction of the arrow (6) in the figure to detach the bracket bar from the outer end of the cable (from the gearbox side).

Pressing the bracket bar in the direction of the arrow (5) in the figure, pry up the outer end of…


Remove the outer end of the selector cable (from the gearbox side) from the bracket.

Remove the clamp from the selector cable end (from the gearbox side).

Remove the clamp from the selector cable end (from the gearbox side).


Remove the selector cable end (from the gearbox side) from the manual shift lever.



Remove the selector cable end (from the gearbox side) from the manual shift lever.


4. Remove the side walls.

5. Remove the clamp shown in the figure and unscrew the nut.

5. Remove the clamp shown in the figure and unscrew the nut.


6. Unscrew the nuts and remove the cover shown in the figure.

6. Unscrew the nuts and remove the cover shown in the figure.


7. Installation is carried out in the reverse order of removal, taking into account the following:

Make sure the selector lever is in position P.

Make sure that the manual shift lever on the gearbox is set to position P.



Make sure that the manual shift lever on the gearbox is set to position P.


Press the locking element in the direction of the arrow (1) in the figure, and then press the safety lock in the direction of the arrow (2) in the figure and lock.

Press the locking element in the direction of the arrow (1) in the figure, and then press the…


Install the outer end of the selector cable (from the gearbox side) on the bracket so that its mark is in the area of the arrow in the figure.

Install the outer end of the selector cable (from the gearbox side) on the bracket so that its mark…
This article is available at: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
This text was checked by: Evgeny Mereshnikov
Share with friends on social networks:

Previous
CX-5KE » Automatic gearbox
Next

Automatic transmission shift mechanism
Removal and installation the valve body
Transmission Control Unit Configuration
Initialization and Configuration Procedures — Initial Training
Removal and installation the gearbox oil cooler
Adjusting the selector drive cable
Removal and installation the selector lever assembly
Removal and installation the selector illumination lamp
Position sensor M
Gear Boost switch
More articles on repairing other Mazda models
Adjusting the gear selector cable Mazda Familia 5 (1985-1989)
Speedometer Drive Cable — removal and installation Mazda Capella 3 (1982-1992, petrol)
Gear Selector Cable Installation Instructions Mazda3 BK (2003-2009)
Gear Selector Cable Installation Instructions Mazda6 GG (2002-2008)
Checking the rubber boots of the drive shafts Mazda 121 (3) (1996-2003)
Link in different formats to this article
Comments and feedback from visitors
No comments yet


How much will 36 + 27 ?

       



CX-5KE (2012-2017) 
  • General information
  • Introduction to the guide
  • User manual
  • Maintenance
  • Power unit
  • Petrol engines 2.0 l
  • Petrol engines 2.5 l
  • Diesel engines 2.2 l
  • Cooling system
  • Lubrication system
  • Supply system
  • Control system
  • Intake and exhaust system
  • Engine electrical equipment
  • Transmission
  • Clutch
  • Mechanical gearbox
  • Automatic gearbox
  • Transfer case
  • Drive shafts and cardan
  • Chassis
  • Wheels and tires
  • Front suspension
  • Rear suspension
  • Brake system
  • Steering
  • Body
  • Exterior (external elements)
  • Interior (internal elements)
  • Security systems
  • Heating and air conditioning
  • Electrical equipment
  • Equipment and devices
  • Electrical circuits
MazBook.ru © 2018–2026 · Mobile version · Articles and news · Sitemap: EN BG BY UA RS HR RO PL SK HU · Feedback · Site search · Add to bookmarks Familia 5 (BF) · Familia 6 (BG) · Capella 3 (GC) · Capella 3 and 4 (GC) · Capella 4 (GD) · Capella 5 (GE) · Capella 6 (GF) · Mazda3 BK · Mazda6 GG · CX-5KE · Mazda 121 (3) · Mazda BT-50 (1) ·
By continuing to use the site, you agree to the use of cookies 🔐