Brake system of the car Mazda 323 (BG)

Description of the brake system
1 - brake line; 2 - brake pedal; 3 - master brake cylinder; 4 - brake booster; 5 - brake pressure distributor; 6 - Front disc brake; 7 - brake caliper; 8 - rear disc...

Technical data of the brake system
brake front brake rear brake brake disc thickness of the new minimum thickness (wear limit) permissible lateral runout (brake disc installed) up to 9/89 and station...

Front brake device
1 - brake hose; 2 - set of brake pads; 3 - bolt; 4 - brake caliper; 5 - brake disc Attention! The version shown is from 10/89, previously other intermediate plates and...

Removal and installation front brake pads
Removal 1. Mark the position of the wheel disc relative to the hub so that the balanced wheel can be installed in its original position. 2. Loosen the wheel nuts of the...

Checking the thickness/lateral runout of the brake disc
1. Brake discs must not be treated. If grooves are deeper than 0.5 mm or if there is severe wear, the disc must be replaced. Always replace both discs on the same axle....

Removal and installation rear disc brake pads
Rear disc brakes are installed on cars with high engine power and/or ABS. A special device is required to screw in the brake piston. If there is no special device, you...

Removal and installation the brake caliper
Removal 1. Remove the brake pads. 2. For rear disc brakes only: Loosen the handbrake cable completely and disconnect the cable from the caliper. 3. If the caliper needs...

Removal and installation the brake disc
To ensure uniform braking on both sides, both brake discs must have the same surface. Therefore, it is essential replace both brake discs on one axle. Cars produced...

Removal and installation rear brake shoes/brake drum
Cars up to 9/89 issue and "station wagon" models 1 - brake drum; 2 - pin and fastening spring; 3 - front and rear brake pads; 4 - return springs; 5 - damping springs; 6...

Removal and installation the wheel brake cylinder
Removal 1. Remove the brake pads. 2. Loosen the union nut of the brake pipe on the wheel cylinder from the back side. Attention! Brake fluid will leak out, place a...

Wheel brake cylinder repair
If the wheel cylinder does not need to be replaced, it can be disassembled in the installed state. The brake shoes should be removed first. The wheel brake cylinder...

Brake fluid — precautions
When handling brake fluid, please note the following: Brake fluid is poisonous. Never suck brake fluid out of the hose with your mouth. Pour brake fluid into containers...

Bleeding the brake system
1. After each brake repair, during which the system was opened, air may be found in the pipes. In this case, the system should be bled. Air is in the system if the...

Replacement of brake lines and hoses
In the brake system, tubes are used as pipelines, which, together with high-pressure hoses, provide the connection of the brakes to the master brake cylinder. Brake...

Checking the brake booster
1. The brake booster should be checked if an unusually large force must be applied to the brake pedal to achieve braking. 2. Press the brake pedal at least 5 times with...

Removal and installation the brake light switch
Caution! For checking the brake light switch, see Chapter Electrical equipment system . The brake light switch is located above the brake pedal on the pedal block....

Handbrake device
1 - rear console; 2 - adjusting nut; 3 - return spring; 4 - middle cable; 5 - nut (disc brakes); 6 — bolt (drum brakes); 7 — bracket; 8 — handbrake cable lubricate...

Adjusting the handbrake
The rear wheel brakes are adjusted automatically, according to the wear of the brake pads. Adjustment of the handbrake is only necessary when replacing the lever or...

Anti-lock braking system (ABS)
Depending on the model and version, the MAZDA 323 can be equipped with an anti-lock braking system (ABS). Additional installation of ABS is not possible. The anti-lock...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Chassis: Brake system Mazda Capella 6 (1997-2005, petrol)
• Chassis: Brake system Mazda3 BK (2003-2009)
• Chassis: Brake system Mazda6 GG (2002-2008)
• Chassis: Brake system Mazda CX-5KE (2012-2017)
• Chassis: Brake system Mazda BT-50 (1) (2006-2011)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code