Brake system of the car Mazda BT-50 1

Checking the brake fluid level
The procedures for checking the brake fluid level are described in Chapter " Maintenance and general check and adjustment procedures ".

Brake system — device
Location of brake system components. 1 - brake fluid reservoir, 2 - vacuum hose, 3 - brake pedal, 4 - brake light switch, 5 - master brake cylinder, 6 - brake booster, 7...

Bleeding the brake system
Note: During bleeding, the brake fluid level in the reservoir should not fall below 3/4 of the set level. Whenever the brake pipes are disconnected, the entire system...

Checking the vacuum hose
1. Remove the vacuum hose clamps and the vacuum hose. 2. Alternately apply pressure and vacuum to the end of the hose connected to the vacuum pump. Make sure that air...

Brake pedal — checking and adjustment
1. Checking the height of the brake pedal. Make sure that the distance between the top surface of the brake pedal pad and the engine compartment bulkhead is within the...

Brake pedal — removal and installation
Ford Ranger The brake pedal is made as a single unit with the clutch and accelerator pedals. For procedures for removing and installing the pedals, see Chapter " Fuel...

Brake light switch
Removal and installation Remove the parts in the order they are numbered in the assembly drawing below. 1 - brake light switch connector, 2 - brake light switch, 3 -...

Removal and installation the master brake cylinder
Ford Ranger Remove the parts in the order of their numbering in the assembly drawing " Removing and installing the master brake cylinder (Ford Ranger)". Removal and...

Disassembly and assembly of the brake master cylinder
Remove the parts in the order they are numbered in the assembly drawing "Master Cylinder". Master brake cylinder (Ford Ranger). 1 - lid and filter, 2 - pin, 3 - brake...

Vacuum brake booster — check
Without using devices Note: If the brake booster is found to be not operating properly, replace the brake booster assembly. Step 1 1. With the engine not running, press...

Vacuum brake booster — removal and installation
1. Remove the brake master cylinder (see the "Brake Master Cylinder" section). 2. (Models with ABS system) Loosen the nuts and disconnect all pipes from the pressure...

Vacuum pump
Examination 1. Start and warm up the engine. 2. Disconnect the hose from the vacuum pump and connect the vacuum gauge as shown in the figure. Check the vacuum value...

Load Sensing Brake Force Redistribution Valve
Examination Note: Before checking, make sure the fuel tank is full, all systems are filled with the rated amount of fluid, and the spare tire, tools and jack are in...

Front brakes — check
1. Check the thickness of the brake shoe linings. a) Jack up the front of the car. b) Remove the wheels. c) Check the thickness of the brake shoe linings. Minimum...

Replacing brake pads
Note: When performing work, refer to the assembly drawing "Replacing brake pads". Do not disconnect the brake hose from the caliper. Otherwise, you will need to perform...

Removal and installation the caliper
Caution: Carrying out further repairs without first removing the ABS wheel speed sensor may damage the sensor wiring. To prevent damage to the sensor or its wiring,...

Disassembling and assembling the caliper
Remove the parts in the order they are numbered in the assembly drawing "Support". Support. 1 - anther, 2 - piston, 3 - sealing cuff, 4 - bleed nipple cap, 5 - bleed...

Rear brakes — check
1. Check the thickness of the brake shoe linings. a) Remove the brake drum. b) Measure the thickness of the brake shoe linings. Minimum thickness of the overlay is 1.0...

Rear brakes — removal and installation
Caution: When removing/installing the brake drum, the spring may jump out and injure you. Use safety glasses or cover the brake drum with a rag when removing. Remove the...

Disassembly and assembly of the working brake cylinder
Note: If any faults are found, replace the slave cylinder assembly. Remove the parts in the order they are numbered in the assembly drawing "Brake Slave Cylinder". Note:...

Parking brake — checking and adjusting
Examination 1. Pull the parking brake lever several times. 2. Press the brake pedal several times. 3. Check the stroke of the parking brake lever. Slowly lift the lever...

Parking brake — device
Location of parking brake components. 1 - parking brake lever, 2 - parking brake drive cable, 3 - parking brake engagement sensor.

Parking brake lever
1. Remove the lower trim on the driver's side. 2. Remove the parts in the order they are numbered in the assembly drawing "Parking brake lever". Parking brake lever. 1 -...

Checking the parking brake sensor
1. Disconnect the parking brake switch connector. 2. Make sure there is continuity between terminal "A" of the sensor and ground when the parking brake is on and there...

Removal and installation parking brake cables
1. Remove the fuel tank guard. 2. Remove the rear brake shoe (see section " Rear brakes "). 3. Remove the parts in the order they are numbered in the assembly drawing...

ABS System Diagnostics — System Description
The electronic control unit has a fail-safe system that can detect a malfunction in the system. When a malfunction is detected, the electronic control unit switches off...

Reading and erasing fault codes
Reading and erasing fault codes is only possible with the diagnostic tool. For detailed information on the procedures for reading and erasing fault codes, see the...

Pressure modulator and ABS control unit
Removal and installation Caution: Do not allow the pressure modulator to fall, as this will damage the internal components. Remove the parts in the order they are...

Front Wheel Speed Sensors — Checking
1. Remove the wheel and check the speed sensor for damage. Replace the sensor if necessary. 2. Check the gap between the wheel speed sensor and the sensor rotor as shown...

Front Wheel Speed Sensors — Removal and Installation
1. (Right sensor) When removing the sensor from the right side of the car, disconnect the connector from the washer reservoir, unscrew the bolts and place the tank...

Rear Wheel Speed Sensors — Check
1. Remove the wheel and check the speed sensor for damage. Replace the sensor if necessary. 2. Check the gap between the wheel speed sensor and the sensor rotor. a)...

Rear Wheel Speed Sensors — Removal and Installation
Remove the parts in the order they are numbered in the assembly drawing "Removing and installing the front wheel speed sensor". Removal and installation the rear wheel...

Slowdown sensor
Removal and installation Caution: Do not drop the deceleration sensor when removing/installing. 1. Move the front passenger seat all the way back. 2. Remove the parts in...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Chassis: Brake system Mazda Familia 5 (1985-1989)
• Chassis: Brake system Mazda Capella 6 (1997-2005, petrol)
• Chassis: Brake system Mazda3 BK (2003-2009)
• Chassis: Brake system Mazda6 GG (2002-2008)
• Chassis: Brake system Mazda CX-5KE (2012-2017)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code