Vehicle owner's manual Mazda BT-50 1

Door lock
1. The kit includes several keys. Depending on the model configuration, keys can be with or without an immobilizer system. Any key allows you to start the engine, unlock...

Anti-theft system
The anti-theft system is designed to protect against unauthorized entry into the car. When the system is triggered, the light alarm is turned on (the direction...

Instrument cluster instruments, gauges and indicators
Instrument panel. 1 - headlight range correction system regulator. 2 - instrument cluster backlight brightness control, 3 - headlight and turn signal switch, 4 -...

Window lifters — general information
1. On models with electric window lifts, the position of the windows is changed by pressing the corresponding switch. In this case, the key in the ignition switch must...

Light signaling on the car
1. Turning on the side lights, headlights, instrument cluster and license plate lighting. Note: The headlight and turn signal switch operates regardless of the position...

Adjusting the brightness of the instrument cluster illumination
The brightness of the instrument cluster illumination is adjusted using the switch located to the left of the steering wheel. To increase/decrease the brightness of the...

Headlight range correction system
The need to adjust the direction of the headlight beam arises depending on the vehicle load. The direction of the headlight beam is adjusted by rotating the headlight...

Hood — General Information
1. To open the hood, you must perform the following procedures: a) Pull the hood release lever located to the left of the steering wheel towards you. b) Raise the hood...

Fuel filler flap
To open the fuel filler flap, press the fuel filler flap lock actuator button located to the left of the steering wheel. Remove the fuel tank filler cap.

Windscreen wiper and washer control switch
The windshield wiper and washer control switch operates when the ignition key is in the "ON" position. 1. To turn the cleaner on and off, move the switch to one of the...

Mirror control
1. The position of the side mirrors is adjusted using the mirror position control panel located on the driver's door panel. The ignition key must be in the "ON" or "ACC"...

Adjusting the position of the steering wheel
To adjust the vertical position of the steering wheel, press the vertical position adjustment lever of the steering wheel down. Further adjustment is made by moving the...

Seats — adjustment
1. Adjusting the longitudinal position of the front seat. To adjust the longitudinal position of the front seat, move the lever up and move the seat to the desired...

Seat belts
To protect you and your passengers in the event of a traffic accident, it is recommended that all people in the vehicle wear seat belts. Attention: Do not wear the...

Precautions when operating vehicles equipped with the SRS system
The SRS air bag system is designed only as a supplement to the primary safety belt system on the driver and front passenger sides. The driver and front passenger should...

Sockets for connecting additional devices
The socket is designed to provide power to various car accessories. Before use, remove the plug from the socket. When using the socket, observe the following conditions:...

Heater and air conditioner
General information 1. The heater and air conditioner operate only when the ignition is on. The heater operation is directly related to the engine coolant temperature,...

Audio system — key points of operation
Radio The quality of radio signal reception may vary significantly while the vehicle is moving due to terrain features, weather conditions and proximity to sources of...

Setting the clock
The clock is set when the ignition key is set to the "ACC" or "ON" position. 1. Press and hold the "CLOCK" button for 2 seconds until a beep is heard. The clock display...

Adjusting volume, balance and tone of sound
Radio tape recorder. 1. "PWR/VOL" switch. Allows you to turn the power on/off. Press the switch once to turn the system on. To turn it off, press the switch again. To...

Tuning and listening to radio stations
1. AM/FM buttons (type 1) or "FM1", "FM2" and "AM" (type 2). Allows you to turn on the radio and switch between FM1/FM2/AM ranges. The display shows the selected range...

Controlling a cassette player
1. Switching the audio system to cassette player mode is done by pressing the "TAPE" button 2. Rewind. To rewind the tape, press the "REW" button (back) or "FF7"/...

Controlling the CD player
1. Turn on the player. Press the "CD" button and turn on the CD player. If a CD is inserted but not playing, pressing this button will start playing the recording. 2....

Controlling the CD player (CD-changer)
Note: The CD-Changer player is controlled in the same way as a CD player (see description above). 1. Turn on the player. Press the "CD" button and turn on the CD player....

Parking brake
To apply the parking brake when parking the vehicle, press the brake pedal and pull the parking brake lever located to the right of the steering wheel toward you. When...

Driving a car with a manual transmission
The gear shift pattern is shown in the figure. The pattern is also shown on the lever handle. Always fully depress the clutch pedal before shifting gears. Attention: Do...

Anti-lock braking system (ABS)
Caution: Use tires of the same size, construction and load capacity as the original vehicle tires, as using a different type of tire may interfere with the proper...

Features of the transmission of 4WD models
Caution: To avoid damage to transmission components, partial loading of 4WD models is prohibited (by raising only one of the vehicle's axles). The all-wheel drive system...

Tips for driving in different conditions
General recommendations Attention: Before driving, make sure that the parking brake is fully released and the corresponding indicator is off. Do not keep your foot on...

Towing a car
Attention: It is strictly forbidden to tow 4WD vehicles using the partial loading method, i.e. by raising one of the vehicle axles. Tow 4WD models only with a rope or...

Towing a trailer
General information 1. Although towing a trailer will have a negative effect on handling, performance, braking, durability and economy, your vehicle may be used as a...

Starting the engine
Ignition switch There are four fixed positions of the ignition switch: LOCK: In this position, you can insert or remove the key from the ignition switch. When the key is...

Engine Start Assist System
This system is used to facilitate engine starting in cold weather and to quickly warm up the engine. The easy starting switch is located on the instrument panel, to the...

Engine malfunctions while driving
Engine stops while driving 1. Reduce speed gradually. Move the car to a safe place. 2. Turn on the hazard warning lights. 3. Try to start the engine. Note: When the...

Spare tire, jack and tools
Jack and tools The jack and tools are stored in the luggage compartment. The kit includes a jack, a jack handle with an extension and tools. Spare wheel To remove the...

Jacking up a car
Before jacking up the car 1. Place the vehicle on a level surface where work can be carried out safely without obstructing traffic. 2. Apply the parking brake. 3. Move...

Wheel replacement
Before changing a wheel 1. Place the vehicle on a level surface where work can be carried out safely without obstructing traffic. 2. Apply the parking brake. 3. Move the...

Recommendations for choosing tires
When choosing tires, pay attention to the marking. Geometric dimensions, load capacity and maximum speed must strictly comply with the manufacturer's recommendations....

Checking tire pressure and condition
1. Check your tires regularly for damage. Check your tire pressure every two weeks or at least once a month. Don't forget to check the pressure in your spare tire. The...

Tire replacement
1. When replacing tires, use only tires of the same size and design as those originally installed, and with the same or greater load capacity. Using a tire of any other...

Features of using aluminum wheels
Caution: To avoid damaging the protective varnish layer, do not allow tire shop workers to clean the outer surface of the rim with a wire brush or remove adhesive...

Replacement of wheel disks
1. Due attention should be paid to replacing wheel rims. Make sure that rims with the same load capacity, diameter, rim width and offset are installed. 2. Incorrect...

Catalytic converter and exhaust system
1. A catalytic converter is a device that reduces the toxicity of exhaust gases. On most models, the catalytic converter is installed under the body. 2. When operating a...

Checking and replacing fuses
If the headlights or other electrical components do not work, check the fuses. If any of the elements are burnt out, they must be replaced. Note: To remove and install...

Replacing lamps
Attention: Before replacing a light bulb, make sure the light switches are turned off. To avoid burns, replace lamps only after they have cooled down. Halogen lamps...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• General information: User manual Mazda Familia 6 (1989-1994)
• General information: User manual Mazda Capella 6 (1997-2005, petrol)
• General information: User manual Mazda CX-5KE (2012-2017)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code