Car rear suspension Mazda BT-50 1
Checking and adjusting the axial clearance in the rear suspension bearing
1. By pushing and pulling the wheel hub with your hands in the axial direction, measure the axial clearance in the wheel bearing. Bearing clearance - 0.05 - 0.25 mm 2....
1. By pushing and pulling the wheel hub with your hands in the axial direction, measure the axial clearance in the wheel bearing. Bearing clearance - 0.05 - 0.25 mm 2....
Rear axle shaft — removal
1. Remove the parts, referring to the figure "Removing and installing the half shaft". Removal and installation the axle shaft. 1 - brake drum, 2 - parking brake cable,...
1. Remove the parts, referring to the figure "Removing and installing the half shaft". Removal and installation the axle shaft. 1 - brake drum, 2 - parking brake cable,...
Rear suspension — device
Rear suspension component locations. 1 - spring, 2 - rear suspension shock absorber, 3 - rear suspension anti-roll bar, 4 - axle shaft assembly with brake mechanism.
Rear suspension component locations. 1 - spring, 2 - rear suspension shock absorber, 3 - rear suspension anti-roll bar, 4 - axle shaft assembly with brake mechanism.
Rear axle shaft — installation
1. Using a drift and hammer, push the oil seal into the rear axle housing. 2. Using a mandrel and press, install the seal and bearing outer race into the bearing...
1. Using a drift and hammer, push the oil seal into the rear axle housing. 2. Using a mandrel and press, install the seal and bearing outer race into the bearing...
Shock absorber and spring of the rear suspension
Removal and installation Note: When installing stands on the left or right side of the vehicle, place a jack under the rear axle and raise/lower it as necessary. Remove...
Removal and installation Note: When installing stands on the left or right side of the vehicle, place a jack under the rear axle and raise/lower it as necessary. Remove...
Rear suspension anti-roll bar
Removal and installation Remove the parts in the order they are numbered in the assembly drawing "Removing and installing the rear suspension stabilizer bar". Removal...
Removal and installation Remove the parts in the order they are numbered in the assembly drawing "Removing and installing the rear suspension stabilizer bar". Removal...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
More sections on repairs of other Mazda models
• Chassis: Rear suspension Mazda Familia 6 (1989-1994)
• Chassis: Rear suspension Mazda Capella 4 (1987-1992)
• Chassis: Rear suspension Mazda CX-5KE (2012-2017)
• Chassis: Rear suspension Mazda Familia 6 (1989-1994)
• Chassis: Rear suspension Mazda Capella 4 (1987-1992)
• Chassis: Rear suspension Mazda CX-5KE (2012-2017)
Link in different formats to this section
TEXTHTMLBB Code
- General information
- Introduction to guide
- User manual
- Maintenance
- Power unit
- Engine repair (diesel)
- Cooling and lubrication system
- Fuel injection system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- All-wheel drive system
- Transfer case and gearboxes
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body
- Exterior (external elements)
- Interior (internal elements)
- Heating and air conditioning
- Security system SRS
- Electrical equipment
- Equipment and devices
- Electrical circuits
- General information
- User manual
- Maintenance
- Power unit
- Petrol engine 1.3 l
- Petrol engine 1.25/1.4 l
- Diesel engine
- Lubrication system
- Cooling system
- Ignition system
- Supply system
- Fuel injection (gasoline)
- Fuel injection (diesel)
- Exhaust system
- Transmission
- Clutch
- Car gearbox
- Chassis
- Front suspension
- Rear suspension
- Steering
- Brake system
- Wheels and tires
- Body
- Exterior (external elements)
- Interior (internal elements)
- Doors, windows and locks
- Heating system
- Electrical equipment
- Troubleshooting
- Equipment and devices
- Lighting system
- Power devices
- Electrical circuits