Specifications and characteristics of car Mazda 626 (4)

Parameters and dimensions
Dimensions and weight Overall length: - Compartment 4450 mm - Limousine 4515 mm - Khachbek 4515 mm Overall width 1690 mm Overall height: - Compartment 1360 mm (14-inch...

General characteristics of the engine
Engine designation: - 1.6-liter F6 — 1.8-liter F8 - 2.0-liter FE (8 or 12 valves) - 2.0-liter engine (two camshafts) FE DOHC - diesel engine RF-N Number and arrangement...

8-valve petrol engine
Cylinder head Cylinder head height 91.95- 92.05 mm Permissible warpage of the cylinder head surface 0.15 mm Permissible warping of the branch pipe 0.10 mm Max....

12-valve engine
Cylinder head Cylinder head height 91.95-92.05 mm Permissible warpage of the cylinder head surface 0.15 mm Permissible warping of the nozzle surface 0.10 mm Max,...

DONS engine (two camshafts)
Cylinder head Cylinder head height 133.95-134.05 mm Permissible warpage of the cylinder head surface 0.15 mm Permissible warping of the nozzle surface 0.10 mm...

Diesel engine
Cylinder head Cylinder head height 133.9-134.1 mm Permissible warpage of the cylinder head surface 0.10 mm max. Permissible warping of the nozzle surface 0.10 mm Max,...

Engine Lubrication — gasoline engine
Lubrication system pressure at 3000 rpm: - more standard engine 3.0-4.0 kgf/cm² — DOHC engine 3.5-4.5 kgf/cm² — min. oil pressure at 100 rpm 1.5-2.5 kgf/cm² Engine oil...

Engine Lubrication — diesel engine
Lubrication system pressure: — at 3000 rpm 3.5-4.5 kgf/cm² — min. pressure at 1000 rpm 1.5-2.5 kgf/cm² Engine oil capacity: - dry engine 6.1 liters - oil bath 5.0 liters...

Cooling system
Design thermosiphon system with circulation thanks to a vane circulation pump, driven by a toothed belt. Thermostatic control, electric fan, on/off switch on the...

Fuel system — carburetor-fe and f8-engine
Design two-stage downdraft carburetor Inlet diameter: - 1st step 30.0 mm - 2nd stage 34.0 mm Diffuser diameter: - 1st step 23.5 mm - 2nd stage 29 mm Main nozzle: — 1st...

Fuel system — carburetor — FE engine
Design two-stage downdraft carburetor Inlet pipe diameter: 1st stage 30.0 mm 2nd stage 34.0 mm Air nozzle diameter: - 1st step 23.5 mm - 2nd stage 29 mm Main nozzle: —...

Fuel injection system — fe engine (single overhead camshaft)
Fuel pump Design in a tank, with an electric motor Fuel pressure 4.5-6.0 atm Performance 220 cm³ per minute Idle speed: — with a stepped gearbox 800+50 rpm — with...

Fuel injection system — fe engine (dohc)
Fuel pump Design in the tank Fuel pressure: - main pump 4.5-6.0 atm — transfer pump 0.20-0.25 atm Performance: Main pump 220 cm³ per minute Transfer pump 190 cm³ Idle...

Diesel fuel system
Injection system pump: Design VE distribution pump Piston diameter 8.0 mm Injection control 0° top dead center Cam stroke during injection control 1.0 mm Nozzle...

Parameters and dimensions — ignition
Ignition distributor drive a screw ring on the camshaft or a driver on the end of the camshaft Ignition timing: Except DOHC engines 6°±1° before top dead center at idle....

Parameters and dimensions — clutch
Design single-disc dry clutch with disc Drive spring hydraulic installation Clutch pedal clearance 5-13 mm Max runout of driven disk 1.0 mm Clutch pedal height...

Transmission
Installed gearbox four- or five-speed gearbox Automatic transmission hydraulic transformer and 3-speed or 4-speed planetary gearbox Gear ratio of the gearbox stage...

Parameters and overall dimensions — differential
Gear ratio: - stepped gearbox 3,850:1,4; 4,105:1 - automatic four-speed 3,700:1 - automatic three-stage 3,450:1 (FE engine), 3,631:1 (F6 engine)

Front axle
Design macPherson strut with coaxial shock absorbers, coil springs, lower wishbones and anti-roll bar Front wheel alignment Convergence -3 mm divergence to +3 mm...

Tire pressure
Ahead 2.0 or 2.2 atm. indicated on the sticker Behind 1.8 atm

Rear wheel suspension
Design Two-wheel steering suspension of individual wheels with parallel wishbones, connecting rods (longitudinal suspension arms), coil springs, hydraulic telescopic...

Steering system
Rack and pinion steering design Free clearance on the steering wheel rim 40 mm max. Steering wheel diameter 380 mm Rotation, from turn to turn: - mechanical control...

Brake system
Design disc brakes at the front and drum brakes at the rear, self-adjusting rear wheel brakes, or disc brakes at the front and rear, with ventilated front discs. With...

Electrical system
Battery Voltage 12 V Power 50 or 60 a. h. Polarity negative case connection Spec. weight. full charge 1.250-1.270 at 20°C Special weight discharge 1,20 Charging current...

Starter specifications
Design starter with forced engagement of gear and magnetic switch or with reduction gear Nominal voltage 12V Power: - stepped gearbox 0.85 kW at 12 V - automatic...

Tightening torque table
Engine, single camshaft Cylinder head 80-86 Nm Cylinder head cover 6-8 Nm Spark plugs 15-23 Nm Drive belt cover 7-10 Nm Exhaust manifold on cylinder head (bolt) 19-30 Nm...

Engine, two camshafts — tightening torques
Cylinder head 80-86 Nm Cover in the center of the cylinder head housing 8-12 Nm Cylinder head cover 4-6 Nm Spark plugs 15-23 Nm Drive belt cover 7-10 Nm Engine mount on...

Diesel engine — tightening torques
Cylinder head: first step 30 Nm second stage pull up 90° third stage pull up 90° Sealing plate 8-12 Nm Rear camshaft timing belt pulley 55-65 Nm Camshaft drive gear...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• General information: Vehicle data Mazda Familia 5 (1985-1989)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

Capella 5 (1991-1997)