Brake system Mazda 626 (3rd and 4th gen)

Brake system specifications
Disc brakes The thickness of the pad is 10 mm Minimum thickness: 1.0 mm Caliper bore diameter: 55 mm Brake disc: Thickness - 14 mm Minimum thickness: 12.5 mm Runout...

General description of the braking system
All models described in this manual have hydraulic brakes. Front brakes are disc, rear brakes are drum. All brakes are self-adjusting. Disc brake pad wear is compensated...

Disc brake pads — replacement
Front disc brake and steering knuckle component locations 1. Brake hose bolt; 2. Caliper mounting bolts; 3. Support; 4. Outer brake shoe; 5. Hub nut; 6. Bolt and nut; 7....

Disc Brake Caliper — removal and installation
Removal 1. Before removing the caliper, unscrew the cap of the brake hydraulic system replenishment reservoir, pump out two-thirds of the fluid into a sealed container...

Disc brake caliper — rebuild
Note: Purchase a caliper rebuild kit. 1. Remove the caliper ( Chapter 3 ) and brake pads ( Chapter 2 ). The caliper piston can be removed in two ways. Step 4 below...

Brake disc — inspection, removal and installation
1. Jack up the vehicle and support it securely on axle stands. 2. Remove the wheel. 3. Remove the caliper assembly ( see Chapter 3 ). Note: There is no need to...

Drum brake shoes — replacement
Rear drum brake component locations 2. Hub nut; 3. Brake drum; 4. Return springs; 5. Brake shoe support posts and their springs; 6. Leading brake shoe; 7. Regulator; 8....

Drum brake master cylinder — removal, overhaul and installation
Removal 1. Jack up and securely support the rear of the vehicle on axle stands. 2. Remove the brake pad assembly ( Chapter 6 ). 3. Carefully clean away any dirt that has...

Master cylinder — removal, overhaul and installation
Master cylinder component locations 1. Liquid level sensor; 2. Torrens system tubes; 3. Nuts; 4. Assembling the master cylinder; 5. Tank lid; 6. Reservoir; 7. Bushings;...

Brake hoses and tubes — inspection and replacement
1. Every six months, jack up the vehicle and inspect the flexible hoses that connect the steel brake lines to the front and rear brake assemblies for cracks, abrasions,...

Parking brake — checking operation and adjustment
Checking the work 1. If the parking brake is adjusted correctly, it should fully engage between 7 and 9 clicks. Adjustment 2. Start the engine, press the brake pedal two...

Brake pedal assembly — removal and installation
Brake pedal assembly components 1. Hairpin; 2. Pin with hole; under the hairpin; 3. Nut; 4. Spring washer; 5. Flat washer; 6. Bolt; 7. Return spring; 8. Pedal; 9....

Parking brake assembly — removal and installation
Parking brake lever assembly parts 1. Screw; 2. Facing; 3. Parking brake switch connector; 4. Adjusting nut; 5. Bolts; 6. Assembling the parking brake lever; 7. Handle;...

Parking brake cables — removal and installation
Rear parking brake cable components 1. Bracket; 2. Connecting the cable to the brake shoe control lever; 3. Bolts; 4. Adjusting nut; 5. Assembling the cable Rear cables...

Brake booster — inspection, removal and installation
Brake booster components 1. Hairpin; 2. Pin with a hole for a stud; 3. Fork and Bunny; 4. Liquid level sensor connector; 5. Brake pipes; 7. Master cylinder assemblies;...

Hydraulic system — bleeding
1. Bleeding the hydraulic system is necessary to remove air from it. 2. You may need to bleed all four brakes if air has entered the system due to low fluid levels, or...

Brake fluid level sensor — checking operation
1. To check the operation of the fluid level sensor, remove the master cylinder reservoir cap. Turn on the ignition. Have an assistant watch the fluid level indicator...

Dual pressure regulating valve — checking operation, removal and installation
Dual pressure regulator 1. Brake pipe; 2. Bolt; 3. Pressure regulator 1. Double pressure regulator is installed on the thermal insulation shield. A precise check...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Chassis: Brake system Mazda Familia 6 (1989-1994)
• Chassis: Brake system Mazda3 BK (2003-2009)
• Chassis: Brake system Mazda6 GG (2002-2008)
• Chassis: Brake system Mazda CX-5KE (2012-2017)
• Chassis: Brake system Mazda BT-50 (1) (2006-2011)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

Capella 5 (1991-1997)